Ge panda warmer service manual

Current Time displays the current day of the week, day, month, year, hour, minutes and seconds. New Time displays the current time until changes are made to the parameters listed on the left of the screen. Page 69 Chapter 4: Troubleshooting Service Mode 4.

The color test pattern should not have drop out or incorrectly displayed colors. The 6 gray scale test patterns display alternate pixels turned on and off, then off and on, in horizontal, vertical, and diagonal patterns. Page 70 Chapter 4: Troubleshooting Service Mode 4. The resettable hour meter, Power Fail counter and Heater Power Values may all be reset to zero from this menu. More detail is displayed below the list for a selected event.

Page 73 Chapter 4: Troubleshooting Service Mode 4. To return to cursor to the left side of the screen press the back key. To return to the log display screen press the back key again.

Page Set Defaults 4. Press the Back key to move the cursor back to the left side of the screen. Press the Back button again to update the display. Press enter on your computer. The buttons are numbered from 1 to 11, starting with the alarm silence button and progressing counter-clockwise.

Page Troubleshooting Information Troubleshooting Information 4. Warning: This is a latex-free device. Latex is not to be used in the maintenance or repair of this device.

Disconnect Mains. Remove Procedure Light Assembly from heater 3 mm Hex head. If short, remove upper housing and continue. Page 87 Chapter 4: Troubleshooting Troubleshooting Tables 4. Using DMM, check resistance on harness pins 3, 6 white wires. Page 88 Chapter 4: Troubleshooting Troubleshooting Tables 4. Bladed screwdriver Disconnect bulb from socket. Replace bulb if continuity test fails. Depending on dimmer pot setting, voltage range will be 8 to 12 VAC.

If no lamp voltage, replace transformer assembly. Page 90 Chapter 4: Troubleshooting Troubleshooting Tables 4. Page 92 Chapter 4: Troubleshooting Troubleshooting Tables 4. Reprogram the main application loading flash. Page 93 Chapter 4: Troubleshooting Troubleshooting Tables 4. Replace Control PCA 4. Page 94 Chapter 4: Troubleshooting Troubleshooting Tables 4. Heater Control Failure. Failure 4. If valid go to Step 6. Check that the power fail Defective buzzer on LED is lit.

Page 98 Chapter 4: Troubleshooting Troubleshooting Tables 4. Too much ambient Also, make sure that procedure light and sunlight observation lights are not at the highest settings, If not OK, replace power supply. If OK, replace Defective probe patient probe. Plug in replacement cable and part : re-test. Replace harness as necessary. Wrench Remove and check fuses F1, F4. Replace as Needle nose pliers, necessary. In addition, check the contacts on Warmer head the Warmer head harness.

Printed Circuit Board. Liquid Crystal Display. Digital Multi-Meter. An electronic measuring instrument that combines several functions in one unit. Digital Multimeter An electronic instrument that measures electrical resistance. Follow your local health and safety guidelines for manual handling of heavy objects when lifting and carrying the heater head. For Wall Mount Warmer models, it is necessary to remove the heater head from the wall bracket to access the rear side of the unit for repairs.

Two of the screws that secure the duct are behind the power supply mounting plates. Heater alignment is also required after the installation of wall mount models. Refer to section 5. Disconnect wire ties from power supply mounting plate using 2 mm hex key. Disconnect ground wire from bracket using 7 mm socket wrench. Using a 3mm hex key, remove the power supply bracket mounting screws. Electronics Enclosure Disassembly 5. Turn lamp off and allow 5 minutes to cool before replacing bulb.

Use a 3 mm hex key to remove the single socket head screw that holds the procedure light in place. This will allow the entire lamp to dangle by its connecting wires. Power Board Panel 5. Caution: Dispose of the battery in accordance with local toxic waste regulations. Display and Touch Panel 5. Loosen the 2 captive screws at the top of the enclosures rear panel, then tilt the panel down and lift the 2 tabs at the bottom of the panel up out of the slots that they seat in.

Do not pry them out use needle nose pliers and pull straight out. For bedded model, tilt the bed so the back is down and the front is all the way up. Disassemble the probe panel housing following instructions 5. Slide the decorative strip down, and remove it from the dovetail. Slide the upper housing forward to remove it from the dovetail rails.

Make sure that you do not pinch the electrical wires. Ensure that foot switch connectors are secured with retaining clips. Base, Legs, and Rails Service Manual Page Chapter 5: Repair Procedures Lower Unit Repairs Bedded and Freestanding Models Re-install the retaining plates in the rails such that the top of the plates are aligned with the top of the mounting block and M8 set screws are located on top see Figure Choose one: Harness Power Factor Correction Please complete the order processing to add an item to the cart.

Please enter Email Address. Remember Me. Please enter Password. Don't know your approval number? Call Enter opt 1 for the first three prompts, and have your System ID available. If you add item s to cart and submit your order without the approval number, GE will contact you before your order can be confirmed for shipment. If you add item s to cart and submit your order without selecting an approver, GE will contact you before your order can be confirmed for shipment.

GE Healthcare will accept, for return from customer, items that are in new condition, unworn, unaltered and free of damage.

Items must be returned in the original packaging, unused and free of damage. Please note, cuffs, BP items and hazmat items cannot be returned. United States. Please Enter Valid Text. Your cart has been saved and will be available when you login next time.

You have a cart already in session. What action do you want to perform? Continue Checkout. I Agree. View Cart Continue Shopping. You already have promotional items in your cart ready to checkout. Adding this "request for a quote" item will require a Quote and prevent checkout. Do you want to continue? The Panda Warmer eliminates alarms during Warmup Mode so you can warm the bed before the baby arrives without disturbing the mother during labor.

Integrated resuscitation and SpO2 options support the latest resuscitation guidelines. Every baby is weighed at birth and our integrated in-bed scale option simplifies the weighing procedure while keeping the baby warm in the process. The Panda Warmer is available with plastic or wood cabinet drawers and trim. When I turn on the machine in pre-warming everything is ok bur in like 10 min working when the system is already warm the observations lights suddenly shut off and I can not turn in on again until the unit is cool again.

Use of these devices may cause serious injuries or death. The oxygen and air wall inlet fittings on the back panel of the resuscitation systems were reversed during assembly. Toggle Navigation. Sign in. My Bench Sign out. One moment please My Bench Close. Sign In.