Nfs2-640 e install manual

An column printout will run the two fields together. Page 22 Programming Basic Program Modify an Addressable Monitor Module Point When you select a point address, the control panel returns a screen that displays information about the point.

Below is an example of information for a monitor module 2M in the LCD display: Blinking Type Code selection character user-editable custom label. Page 23 Basic Program Programming Modify an Addressable Control Module Point When you select a point address for modification, the control panel returns a screen that displays information about the point. For example, the illustration below shows sample information for a control module 2M in the LCD display.

Page 24 Programming Basic Program Table 2. The programmer may hit escape and reenter the password correctly. However, if the password has been forgotten, record the code and contact Notifier.

After proper authentication, the original password can be determined by deciphering the code. Page 28 Programming Basic Program Table 2. Page 29 Basic Program Programming Table 2. Page 32 Programming Basic Program Table 2. This is not required for displayless systems.

The table below contains a list of these groups, what an annunciator displays when a group is selected, and where to locate a definition of the 64 points within the group.

Page 35 Basic Program Programming Table 2. Page 38 Programming Basic Program Table 2. The Check option searches the program for the following Program Change conditions that can cause errors: Password Page The Utility Program Programming The Utility Program To select network options, follow these steps: Using the arrow keys, move the blinking cursor to a selection. Press the key to select H or L Threshold Ch. A, Threshold Ch.

These operating parameters do not affect control program settings. For example, the Status Change password lets you change settings such as detector sensitivity and system time and date. Releasing devices must be physically disconnected. NOTE: When an input or output point associated with releasing functions is disabled, a single supervisory trouble will be generated.

There are two kinds of Walk Test - Basic and Advanced, described later in this section. The activations are tracking; once the activation stimulus is removed, the input will deactivate.

Each input activation is latching; that is, it will not deactivate until the system is reset. Page A. Do not enter the protected space unless physical lockout and other safety procedures are fully completed. Do not use software disable functions in the panel as lockout. In a properly configured system with compatible, listed actuating and initiating devices, this control panel complies with the following NFPA standards for installation in accordance with the acceptable standard: Table A.

Page 63 How to Program a Releasing Zone Releasing Applications When an initiating device activates, you must press and hold the Abort Switch or the control panel will send the command to dump releasing agents when the Delay time 15 seconds shown expires. To change another field on the screen, move the cursor into position by pressing the arrow keys on the keypad. This section details how to program each of these Type Codes.

Type Codes designed for Releasing Zone inputs monitor modules. Releasing begins after the delay timer has expired 15 seconds. Releasing will continue for the soak timer duration 30 seconds. Once the Soak Timer expires, the Second Shot Switch can then be activated to initiate an additional soak cycle.

You can use multiple initiating devices for the same releasing hazard. Page B. Purpose Presignal is a feature that initially causes alarm signals to only sound in specific areas, monitored by qualified persons. This allows delay of the alarm up to seconds after the start of alarm processing. Page C.

You can program Intelligent Sensing functions on a global or on a per-detector basis. In this Self- Optimizing mode, the software measures the normal peak analog readings and sets the Pre-Alarm level just above these normal peaks. This allows extremely sensitive Pre-Alarm capability with reasonable protection against non-fire signals.

Supports one to 10 Signaling line Aug 4, Mount 4. Mount 47K resis-. ECS Series. Aug 20, When used with the. An automatic fire alarm system—typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control panel with remote notification capability—can provide early warning of a develop - ing fire. Such a system, however, does not assure protection against property Speed of Installation.

With the NFS's auto-program feature, fire protection can be established in seconds. Additional programming can be accomplished with the built-in.

Honeywell International, Inc. This includes fire detection and alarm notification, Document DOC Rev: Fire Alarm Control Panel. Installation Manual. Australian Edition Please note this email address is for FACP Model. Firmware Revision. Jul 26, NFS E 4. Section 2. NFS E C 4. NSP 2. All Rights Reserved. Designed by Templatic. Home Copyright Privacy Contact. Notifier Nfs Operating Manual. Sponsored High Speed Downloads. BACnet Gateway-3 May 6, Price List Jun 15, APS-6R Aug 20,